8A34042集成電路（IC）的時(shí)鐘發(fā)生器PLL頻率合成器規(guī)格書PDF中文資料

Features

? Close-in phase noise complies with Common Public Radio

Interface (CPRI) frequency synchronization requirements

? Supports all ITU-T G.709 frequencies

? Meets OTN jitter and wander requirements per ITU-T G.8251

? Four independent timing channels

? Each can act as a frequency synthesizer, jitter attenuator,

Digitally Controlled Oscillator (DCO), or Digital Phase Lock

Loop (DPLL)

? DPLL Digital Loop Filters (DLFs) are programmable with cut

off frequencies from 1.1Hz to 22kHz

? Generates output frequencies that are independent of input

frequencies via a Fractional Output Divider (FOD)

? Each FOD supports output phase tuning with 50ps

resolution

? 8 Differential / 16 LVCMOS outputs

? Frequencies from 0.5Hz to 1GHz (250MHz for LVCMOS)

? Jitter below 150fs RMS (10kHz to 20MHz)

? LVCMOS, LVDS, LVPECL, HCSL, CML, SSTL, and HSTL

output modes supported

? Differential output swing is selectable: 400mV / 650mV /

800mV / 910mV

? Independent output voltages of 3.3V, 2.5V, or 1.8V

? LVCMOS additionally supports 1.5V or 1.2V

? The clock phase of each output is individually programmable

in 1ns to 2ns steps with a total range of ±180°

? 7 differential / 14 single-ended clock inputs

? Support frequencies from 1kHz to 1GHz

? Any input can be mapped to any or all of the timing channels

? Redundant inputs frequency independent of each other

? Any input can be designated as external frame/sync pulse of

PPES (pulse per even second), 1PPS (Pulse per Second),

5PPS, 10 PPS, 50Hz, 100Hz, 1 kHz, 2kHz, 4kHz, and 8kHz

associated with a selectable reference clock input

? Per-input programmable phase offset of up to ±1.638?s in

50ps steps

? Reference monitors qualify/disqualify references depending on

LOS, activity, frequency monitoring, and/or LOS input pins

? Loss of Signal (LOS) input pins (via GPIOs) can be assigned

to any input clock reference

? Automatic reference selection state machines select the active

reference for each DPLL based on the reference monitors,

priority tables, revertive / non-revertive, and other

programmable settings

? System APLL operates from fundamental-mode crystal:

25MHz to 54MHz or from a crystal oscillator

? System DPLL accepts an XO, TCXO, or OCXO operating at

virtually any frequency from 1MHz to 150MHz

? DPLLs can be configured as DCOs to synthesize clocks under

the control of an external algorithm

? DCOs generate PTP based clocks with frequency resolution

less than 1.11 × 10-16

? Supports 1MHz I2

C or 50MHz SPI serial processor ports

? The device can configure itself automatically after reset via:

? Internal customer definable One-Time Programmable

memory with up to 16 different configurations

? Standard external I2

C EPROM via separate I2

C Master Port

? 1149.1 JTAG Boundary Scan

? 10 × 10 mm 72-VFQFN package

Description

The 8A34042 Four-Channel Universal Frequency Translator is a highly integrated timing device that generates synchronous or

asynchronous clocks from any of its reference inputs. The device can be is used in any synthesizer or jitter attenuator application,

including Optical Transport Network (OTN), and Synchronous Ethernet (SyncE) systems.

The internal System APLL must be supplied with a low phase noise reference clock with frequency between 25MHz and 54MHz. The

output of the System APLL is used for clock synthesis by all of the Fractional Output Dividers (FODs) in the device. The System APLL

reference can come from an external crystal oscillator connected to the OSCI pin or from an internal oscillator that uses a crystal

connected between the OSCI and OSCO pins.