GENERAL DESCRIPTION

The AD7664 is a 16-bit, 570 kSPS, charge redistribution SAR, analog-to-digital converter that operates from a single 5 V power supply. The part contains a high speed 16-bit sampling ADC, an internal conversion clock, error correction circuits, and both serial and parallel system interface ports.

The AD7664 is hardware factory-calibrated and is comprehensively tested to ensure such ac parameters as signal-to-noise ratio (SNR) and total harmonic distortion (THD), in addition to the more traditional dc parameters of gain, offset, and linearity.

It features a very high sampling rate mode (Warp), a fast mode (Normal) for asynchronous conversion rate applications, and for low power applications, a reduced power mode (Impulse) where the power is scaled with the throughput.

It is fabricated using Analog Devices’ high performance, 0.6 micron CMOS process, with correspondingly low cost and is available in a 48-lead LQFP and a tiny 48-lead LFCSP with operation specified from –40°C to +85°C.

FEATURES

Throughput:

570 kSPS (Warp Mode)

500 kSPS (Normal Mode)

444 kSPS (Impulse Mode)

INL: ±2.5 LSB Max (±0.0038 of Full Scale)

16-Bit Resolution with No Missing Codes

S/(N+D): 90 dB Typ @ 45 kHz

THD: –100 dB Typ @ 45 kHz

Analog Input Voltage Range: 0 V to 2.5 V

Both AC and DC Specifications

No Pipeline Delay

Parallel and Serial 5 V/3 V Interface

SPI?/QSPI?/MICROWIRE?/DSP Compatible

Single 5 V Supply Operation

Power Dissipation

115 mW Maximum,

21 μW @ 100 SPS

Power-Down Mode: 7 W Max

Package: 48-Lead Quad Flat Pack (LQFP)

48-Lead Chip Scale Package (LFCSP)

Pin-to-Pin Compatible Upgrade of the AD7660

APPLICATIONS

Data Acquisition

Instrumentation

Digital Signal Processing

Spectrum Analysis

Medical Instruments

Battery-Powered Systems

Process Control

AD7677屬于集成電路（IC） > 模數轉換器（ADC）。亞德諾半導體技術有限公司制造生產的AD7677模數轉換器（ADC）模數轉換器（ADC、A/D 或 A 轉 D）對模擬信號進行采樣，例如由麥克風采集的聲音或傳感器的輸出，然后將其轉換為數字信號。一般來說，數字輸出是二進制補碼二進制數，與輸入成比例。輸入類型可能是差分、偽差分或單端輸入。模數轉換器可按照位數、采樣率、輸入數、接口、轉換器數和架構（例如自適應增量、雙斜率、折疊、流水線、SAR、三角積分、兩步式）進行選擇。