ATSAM3U4/2/1 Description

Atmels SAM3U series is a member of a family of Flash microcontrollers based on the high performance 32-bit ARM Cortex-M3 RISC processor. It operates at a maximum speed of 96 MHz and features up to 256 Kbytes of Flash and up to 52 Kbytes of SRAM. The peripheral set includes a High Speed USB Device port with embedded transceiver, a High Speed MCI for SDIO/SD/MMC, an External Bus Interface with NAND Flash controller, up to 4xUSARTs (SAM3U1C/2C/4C have 3), up to 2xTWIs (SAM3U1C/2C/4C have 1), up to 5xSPIs SAM3U1C/2C/4C have 4), as well as 4xPWM timers, 3xgeneral purpose 16-bit timers, an RTC, a 12-bit ADC and a 10-bit ADC.

Features

? Core

– ARM? Cortex?-M3 revision 2.0 running at up to 96 MHz

– Memory Protection Unit (MPU)

– Thumb?-2 instruction set

? Memories

– From 64 to 256 Kbytes embedded Flash, 128-bit wide access, memory accelerator, dual bank

– From 16 to 48 Kbytes embedded SRAM with dual banks

– 16 Kbytes ROM with embedded bootloader routines (UART, USB) and IAP routines

– Static Memory Controller (SMC): SRAM, NOR, NAND support. NAND Flash controller with 4 Kbytes RAM buffer and ECC

? System

– Embedded voltage regulator for single supply operation

– POR, BOD and Watchdog for safe reset

– Quartz or resonator oscillators: 3 to 20 MHz main and optional low power 32.768 kHz for RTC or device clock.

– High precision 8/12 MHz factory trimmed internal RC oscillator with 4 MHz Default Frequency for fast device startup

– Slow Clock Internal RC oscillator as permanent clock for device clock in low power mode

– One PLL for device clock and one dedicated PLL for USB 2.0 High Speed Device

– Up to 17 peripheral DMA (PDC) channels and 4-channel central DMA

? Low Power Modes

– Sleep and Backup modes, down to 2.5 μA in Backup mode

– Backup domain: VDDBU pin, RTC, 32 backup registers

– Ultra low power RTC: 0.6 μA

? Peripherals

– USB 2.0 Device: 480 Mbps, 4-kbyte FIFO, up to 7 bidirectional Endpoints, dedicated DMA

– Up to 4 USARTs (ISO7816, IrDA?, Flow Control, SPI, Manchester support) and one UART

– Up to 2 TWI (I2C compatible), 1 SPI, 1 SSC (I2S), 1 HSMCI (SDIO/SD/MMC)

– 3-Channel 16-bit Timer/Counter (TC) for capture, compare and PWM

– 4-channel 16-bit PWM (PWMC)

– 32-bit Real Time Timer (RTT) and RTC with calendar and alarm features

– 8-channel 12-bit 1MSPS ADC with differential input mode and programmable gain stage, 8-channel 10-bit ADC

? I/O

– Up to 96 I/O lines with external interrupt capability (edge or level sensitivity), debouncing, glitch filtering and on-die Series Resistor Termination

– Three 32-bit Parallel Input/Outputs (PIO)

? Packages

– 100-lead LQFP, 14 x 14 mm, pitch 0.5 mm

– 100-ball TFBGA, 9 x 9 mm, pitch 0.8 mm

– 144-lead LQFP, 20 x 20 mm, pitch 0.5 mm

– 144-ball LFBGA, 10 x 10 mm, pitch 0.8 mm