EM783集成電路（IC）的應(yīng)用特定微控制器規(guī)格書PDF中文資料

General description

The EM783-SC/SP/TP/MC3/MC6 is an ARM Cortex-M0-based, low-cost 32-bit family of

application processors, designed for energy measurement and monitoring applications.

The EM783 offers programmability and on-chip metrology functionality combined with a

low power, simple instruction set. It also has memory addressing together with reduced

code size compared to existing 8/16-bit architectures.

The EM783 operate at CPU frequencies of up to 48 MHz.

The digital peripherals on the EM783 include:

? 32 kB of flash memory

? 4 kB of EEPROM data memory

? 8 kB of SRAM data memory

? Fast-mode Plus I2C-bus interface

? RS-485/EIA-485 USART

? one SSP controller

? two general-purpose counter/timers

? up to 22 general-purpose I/O pins

A metrology engine with built-in temperature sensor is used for energy measurements. A

10-bit DAC and an internal voltage reference are also available.

Features and benefits

? System:

? ARM Cortex-M0 processor, running at frequencies of up to 48 MHz.

? ARM Cortex-M0 built-in Nested Vectored Interrupt Controller (NVIC).

? Serial Wire Debug (SWD).

? System tick timer.

? Memory:

? 32 kB on-chip flash program memory.

? 4 kB on-chip EEPROM data memory for energy registers and calibration

parameters; byte erasable and byte programmable.

? 8 kB SRAM data memory.

? 16 kB boot ROM.

? In-System Programming (ISP) for flash and In-Application Programming (IAP) for

flash and EEPROM via on-chip bootloader software.

? Includes ROM-based 32-bit integer division routines.

? Digital peripherals:

? Up to 22 General Purpose I/O (GPIO) pins with configurable pull-up/pull-down

resistors, repeater mode, and open-drain mode.

? Up to 9 pins are configurable with a digital input glitch filter for removing glitches

with widths of 10 ns. Two pins are configurable for 20ns glitch filter and another

two pins are configurable for 50 ns glitch filters.

? GPIO pins can be used as edge and level sensitive interrupt sources.

? High-current source output driver (20 mA) on one pin (P0_21).

? High-current sink driver (20 mA) on true open-drain pins (P0_2 and P0_3).

? Two general-purpose counter/timers with a total of up to four capture inputs and

five match outputs.

? Programmable Windowed WatchDog Timer (WWDT) with a dedicated, internal

low-power WatchDog Oscillator (WDOsc).

? Analog peripherals:

? Metrology engine for smart metering with one voltage input, one bias input, from

two up to six current inputs and a temperature sensor.

? Internal voltage reference.

? 10-bit DAC with flexible conversion triggering.

? Serial interfaces:

? USART with fractional baud rate generation, internal FIFO, support for

RS-485/9-bit mode and synchronous mode.

? One SSP controller with FIFO and multi-protocol capabilities.

? I2C-bus interface supporting the full I2C-bus specification and Fast-mode Plus with

a data rate of 1 Mbit/s with multiple address recognition and monitor mode.

? Clock generation:

? Crystal Oscillator (SysOsc) with an operating range of 1 MHz to 25 MHz.

? 12 MHz internal RC Oscillator (IRC) trimmed to 1 accuracy that can optionally be

used as a system clock.

? Internal low-power, Low-Frequency Oscillator (LFOsc) with programmable

frequency output.

? Clock input for external system clock (25 MHz typical).

? PLL allows CPU operation up to the maximum CPU rate with the IRC, the external

clock, or the SysOsc as clock sources.

? Clock output function with divider that can reflect the SysOsc, the IRC, the main

clock, or the LFOsc.

? Power control:

? Supports ARM Cortex-M0 Sleep mode as reduced power mode.

? Power profiles residing in boot ROM allowed to optimize performance and

minimize power consumption for any given application through one simple function

call.

? Processor wake-up from reduced power mode using any interrupt.

? Power-On Reset (POR).

? BrownOut Detect (BOD) with two separate programmable thresholds for interrupt

and one hardware controlled reset trip point.

? POR and BOD are always enabled for rapid UVLO protection against power supply

voltage drops below 2.4 V.

? Unique device serial number for identification.

? Single 3.3 V power supply (2.6 V to 3.6 V).

? Temperature range ?40 ?C to +85 ?C.

? Available as a 33-pin HVQFN 7 mm ? 7 mm ? 0.85 mm package.

Applications

? Smart plugs and plug meters

? Single phase residential meters

? Industrial submeters

? Server power monitoring

? Smart appliances