FF450R12IE4分立半導體產品的晶體管-IGBT-模塊規格書PDF中文資料

FF450R12IE4屬于分立半導體產品的晶體管-IGBT-模塊。由英飛凌科技股份公司制造生產的FF450R12IE4晶體管 - IGBT - 模塊絕緣柵雙極晶體管 (IGBT) 是三端功率半導體器件，主要用作電子開關，兼具高效率和快速切換優點。作為模塊，IGBT 配置為非對稱式橋； 升壓、降壓和制動斬波器；全橋、三電平和三相逆變器。有些器件內置了用于監控溫度的 NTC 熱敏電阻。IGBT 模塊可根據最大功率、集電極電流、集射擊穿電壓和配置進行區分。

1 Introduction

The 2ED250E12-F evaluation driver board shown in Fig. 1 was developed to support customers during their

first design steps with the 1200V PrimePACK? IGBT module. The evaluation driver board is a fully

functional IGBT module driver where two 1ED020I12-F driver IC process control and feedback signals and

provide galvanic insulation. An embedded isolated DC/DC converter supplies gate drive power to both IGBTs

of a halbridge configuration.

The 2ED250E12-F Evaluation driver boards are available from Infineon in small quantities. Functions and

properties of these parts are described in the datasheet chapter of this document whereas the remaining

paragraphs provide information intended to enable the customer to copy, modify and qualify the design for

production according to his specific requirements.

The design of the 2ED250E12-F was performed with respect to the environmental conditions described as

design target in this document. The requirements for leadfree reflow soldering have been considered when

components were selected. The design was tested as described in this documentation but not qualified

regarding manufacturing and operation in the whole operating ambient temperature range or lifetime.

The boards provided by Infineon are subjected to functional testing only.

Due to their purpose evaluation boards are not subjected to the same procedures regarding Returned

Material Analysis (RMA), Process Change Notification (PCN) and Product Discontinuation (PD) as regular products.

See Legal Disclaimer and Warnings for further restrictions on Infineon warranty and liability.

2 Design features

Electric features of the evaluation board and mechanical dimensions including interface connections are presented in following sections.

2.1 Main features

The 2ED250E12-F Evaluation Driver Board offers the following features:

? Dual channel IGBT driver utilising the 1ED020I12-F1 driver IC

? Electrically and mechanically suitable for PrimePACK? modules 1200V family

? Integrated isolated DC/DC power supply

? Integrated protection against DC/DC power supply short circuit

? Under Voltage Lockout

? Positive logic with CMOS logic level (5V) for PWM and Fault signals. Can be converted to negative logic

? Separated fault output and ready signal for Top and Bottom IGBT

? Separated ground potential for DC/DC power supply and input logic

? Different gate resistor values for turning-on and -off are possible

? IGBTs are protected against temporary VCE overvoltages during turn-off (Active Clamping)

? Diodes for IGBT desaturation monitoring implemented (short circuit protection)

? All components, except DC/DC transformer, are surface mount devices (SMD) with lead free 260°C

soldering profile

? PCB is designed to fulfil the requirements of IEC61800-5-1, pollution degree 2, overvoltage category III