OVERVIEW

The LAN950x is a high performance solution for USB to 10/100 Ethernet port bridging. With applications ranging from embedded systems, set-top boxes, and PVRs, to USB port replicators, USB to Ethernet dongles, and test instrumentation, the device is targeted as a high performance, low cost USB/Ethernet connectivity solution.

The LAN950x contains an integrated 10/100 Ethernet PHY, USB PHY, Hi-Speed USB 2.0 device controller, 10/100 Ethernet MAC, TAP controller, EEPROM controller, and a FIFO controller with a total of 30 KB of internal packet buffering. Two KB of buffer memory are allocated to the Transaction Layer Interface (TLI), while 28 KB are allocated to the FIFO Controller (FCT).

The internal USB 2.0 device controller and USB PHY are compliant with the USB 2.0 Hi-Speed standard. The device implements Control, Interrupt, Bulk-in, and Bulk-out USB Endpoints.

Highlights

? Single Chip Hi-Speed USB 2.0 to 10/100 Ethernet Controller

? Integrated 10/100 Ethernet MAC with Full-Duplex Support

? Integrated 10/100 Ethernet PHY with HP AutoMDIX support

? Integrated USB 2.0 Hi-Speed Device Controller

? Integrated USB 2.0 Hi-Speed PHY

? Implements Reduced Power Operating Modes

Target Applications

? Embedded Systems

? Set-Top Boxes

? PVRs

? CE Devices

? Networked Printers

? USB Port Replicators

? Standalone USB to Ethernet Dongles

? Test Instrumentation

? Industrial

Key Features

? USB Device Controller

- Fully compliant with Hi-Speed Universal

Serial Bus Specification Revision 2.0

- Supports HS (480 Mbps) and FS (12 Mbps) modes

- Four endpoints supported

- Supports vendor specific commands

- Integrated USB 2.0 PHY

- Remote wakeup supported

? High-Performance 10/100 Ethernet Controller

- Fully compliant with IEEE802.3/802.3u

- Integrated Ethernet MAC and PHY

- 10BASE-T and 100BASE-TX support

- Full- and half-duplex support

- Full- and half-duplex flow control

- Preamble generation and removal

- Automatic 32-bit CRC generation and checking

- Automatic payload padding and pad removal

- Loop-back modes

- TCP/UDP/IP/ICMP checksum offload support

- Flexible address filtering modes

–One 48-bit perfect address

–64 hash-filtered multicast addresses

–Pass all multicast

–Promiscuous mode

–Inverse filtering

–Pass all incoming with status report

- Wakeup packet support

- Integrated Ethernet PHY

–Auto-negotiation

–Automatic polarity detection and correction

–HP Auto-MDIX support

–Link status change wake-up detection

- Support for 3 status LEDs

- External MII and Turbo MII support HomePNA? and HomePlug? PHY

? Power and I/Os

- Various low power modes

- NetDetach feature increases battery life1

- Supports PCI-like PME wake1

- 11 GPIOs

- Supports bus-powered and self-powered operation

- Integrated power-on reset circuit

- Single external 3.3v I/O supply

–Internal core regulator

? Miscellaneous Features

- EEPROM Controller

- Supports custom operation without EEPROM1

- IEEE 1149.1 (JTAG) Boundary Scan

- Requires single 25 MHz crystal

? Software

- Windows XP/Vista Driver

- Linux Driver

- Win CE Driver

- MAC OS Driver

- EEPROM Utility

? Packaging

- 56-pin QFN (8x8 mm) RoHS Compliant Environmental

- Commercial Temperature Range (0°C to +70°C)

- Industrial Temperature Range (-40°C to +85°C)

LAN9500AI屬于集成電路（IC） > 控制器。微芯科技股份有限公司制造生產的LAN9500AI控制器該系列產品主要用于在采用不同通信協議和/或信令方法的端點之間提供信息連接。示例包括將 I2C 總線連接到 UART，將 USB 連接到 I2C、SPI、以太網或 UART、以太網 MAC 和 PHY 等的器件。此外，還包括用于通過為點對點通信設計的接口建立多路連接的器件，例如 USB 集線器控制器。