MAX22205開發板套件編程器的評估演示板及套件規格書PDF中文資料

MAX22205屬于開發板套件編程器的評估演示板及套件。由亞德諾半導體技術有限公司制造生產的MAX22205評估和演示板及套件該系列產品提供了一種方便的方法，在經過驗證的實施環境中評估某些重點器件的性能或特性。評估方法通常有完善的文檔說明，并且視乎具體情況由評估軟件提供支持。產品通常由印刷電路板組成，板上已裝有重點器件以及必要或有用的支持元器件，另外也可能包括其他組件，例如電纜或電源。對于數量特別多或類別獨特的器件類別(如 ADC、DAC 和開關模式電源)，評估平臺可組合為一個單獨的產品系列。

General Description

The MAX22205 integrates a high current 65V, 7.6AMAX

H-Bridge to drive one Brushed DC motor or one half Stepper motor. The H-Bridge FETs feature very low impedance, resulting in high driving efficiency and low heat. The

typical total RON (high-side + low-side) is 0.15?. The HBridge can be PWM controlled by two logic inputs (DINA,

DINB). A third Enable (EN) logic input can be used to configure the outputs to high impedance for coasting the motor.

The MAX22205 features an accurate optional Current Drive Regulation (CDR), which can be used to limit the start

up current of a Brushed DC motor or control the phase

current for stepper operation. The bridge output current is

sensed by a non-dissipative Integrated Current Sensing

(ICS) and it is then compared with the desired threshold

current. As soon as the bridge current exceeds the threshold (ITRIP), the device enforces the decay for a fixed OFFtime (tOFF). The non-dissipative ICS eliminates the bulky

external power resistors normally required for this function, resulting in a dramatic space and power saving compared with mainstream applications based on the external sense resistor. A current proportional to the internally-sensed motor current is output to the analog pins (ISENA, ISENB) to monitor current. Also, one open-drain output (CDR pin) is asserted every time the internal current

regulation is taking control of the driver so that the activity

of the internal current loop can be monitored.

The maximum output current per H-Bridge is IMAX =

7.6AMAX limited by the Overcurrent Protection (OCP). The

device delivers up to 4ARMS at VM = +24V and TA = 25°C

with proper PCB ground plane for thermal dissipation. The

current capability depends on the PCB thermal characteristic (PCB ground planes, heatsinks, ventilation, etc.).

The MAX22205 features Overcurrent Protection (OCP),

Thermal Shutdown (TSD), and Undervoltage Lockout

(UVLO). An open-drain active low FAULT pin is activated

every time a fault condition is detected. During Thermal

Shutdown and Undervoltage Lockout, all the channels are

disabled until normal operating conditions are restored.

The MAX22205 is packaged into a small TQFN38 5mm x

7mm and TSSOP38 9.7mm x 4.4mm packages.

Applications

● Brushed DC Motor Driver

● Stepper Motor Driver

● Solenoid Driver

● Latched Valves

Benefits and Features

● One H-Bridge with +65V Voltage Rating

? Total RDS(ON) (High-Side + Low-Side): 150m?

Typical (TA = 25°C)

● Current Ratings per H-Bridge (Typical at 25°C):

? IMAX = 7.6AMAX (Impulsive Current for Driving

Capacitive Loads)

? IFS = 6A (Max Full Scale Current Setting for Internal

Current Drive Regulation)

? IRMS = 4ARMS (TA = 25°C, VM = +24V)

● Integrated Current Control

? Full-Scale DAC Current Configurable with External

Resistance

? Internal Current Sensing (ICS) Eliminates External

Bulky Resistors and Improves Efficiency

? Current Drive Regulation Monitor Output Pin (CDR

Pin)

? Integrated DAC Sets the Output Current Level

among 16 Values

? Multiple Decay Modes (Slow, Mixed, Fast)

? Fixed OFF Time Configurable with External

Resistance

● Current-Sense Output (Current Monitor)

● Fault Indicator Pin (FAULT)

● Protections

? Overcurrent Protection for each Individual Channel

(OCP)

? Undervoltage Lockout (UVLO)

? Thermal Shutdown TJ = 155°C (TSD)

● Available in TQFN38 5mm x 7mm and TSSOP38

9.7mm x 4.4mm Packages