MC68HC908GT16CFB集成電路（IC）的微控制器規(guī)格書PDF中文資料

General Description

Introduction

The MC68HC908GT16, MC68HC908GT8, and MC68HC08GT16 are members of the low-cost, high-performance M68HC08 Family of 8-bit microcontroller units (MCUs). All MCUs in the family use the enhanced M68HC08 central processor unit (CPU08) and are available with a variety of modules, memory sizes and types, and package types.

Features

For convenience, features have been organized to reflect:

? Standard features of the MC68HC908GT16/MC68HC908GT8

? Features of the CPU08

Standard Features of the MC68HC908GT16/MC68HC908GT8

? High-performance M68HC08 architecture optimized for C-compilers

? Fully upward-compatible object code with M6805, M146805, and M68HC05 Families

? 8-MHz internal bus frequency

? Internal oscillator requiring no external components:

– Software selectable bus frequencies

– ±25 percent accuracy with trim capability to ±4 percent

– Clock monitor

– Option to allow use of external clock source or external crystal/ceramic resonator

? Flash program memory security(1)

? On-chip programming firmware for use with host personal computer which does not require high voltage for entry

? In-system programming (ISP)

? System protection features:

– Optional computer operating properly (COP) reset

– Low-voltage detection with optional reset and selectable trip points for 3.0-V and 5.0-V operation

– Illegal opcode detection with reset

– Illegal address detection with reset

? Low-power design; fully static with stop and wait modes

? Standard low-power modes of operation:

– Wait mode

– Stop mode

? Master reset pin and power-on reset (POR)

? 16 Kbytes of on-chip 100k cycle write/erase capable Flash memory (8 Kbytes on MC68HC908GT8)

? 512 bytes of on-chip random-access memory (RAM)

? 720 bytes of Flash programming routines ROM

? Serial peripheral interface module (SPI)

? Serial communications interface module (SCI)

? Two 16-bit, 2-channel timer interface modules (TIM1 and TIM2) with selectable input capture, output compare, and pulse-width modulation (PWM) capability on each channel

? 8-channel, 8-bit successive approximation analog-to-digital converter (ADC)

? Break module (BRK) to allow single breakpoint setting during in-circuit debugging

? Internal pullups on IRQ and RST to reduce customer system cost

? Up to 36 general-purpose input/output (I/O) pins, including:

– 28 shared-function I/O pins

– Six or eight dedicated I/O pins, depending on package choice

? Selectable pullups on inputs only on ports A, C, and D. Selection is on an individual port bit basis.

During output mode, pullups are disengaged.

? High current 10-mA sink/10-mA source capability on all port pins

? Higher current 20-mA sink/source capability on PTC0–PTC4

? Timebase module with clock prescaler circuitry for eight user selectable periodic real-time interrupts with optional active clock source during stop mode for periodic wakeup from stop using an external 32-kHz crystal or internal oscillator

? User selection of having the oscillator enabled or disabled during stop mode

? 8-bit keyboard wakeup port

? Available packages:

– 42-pin shrink dual in-line package (SDIP)

– 44-pin quad flat pack (QFP)

? Specific features of the MC68HC908GT16 in 42-pin SDIP are:

– Port C is only 5 bits: PTC0–PTC4

– Port D is 8 bits: PTD0–PTD7; dual 2-channel TIM modules

? Specific features of the MC68HC908GT16 in 44-pin QFP are:

– Port C is 7 bits: PTC0–PTC6

– Port D is 8 bits: PTD0–PTD7; dual 2-channel TIM modules