MCP16363集成電路（IC）的PMIC-穩壓器-DCDC開關式控制器規格書PDF中文資料

MCP16363屬于集成電路（IC）的PMIC-穩壓器-DCDC開關式控制器。由微芯科技股份有限公司制造生產的MCP16363DC-DC 開關控制器PMIC（電源管理集成電路）DC 到 DC 開關式控制器是用于高效率電路的穩壓 IC，其配置為生成高于（突升或步升）或低于（突降或步降）輸入電源的輸出電源電壓。其他拓撲結構可能包括：降壓-升壓、反激、正激、Cuk、SEPIC、全橋、半橋和推挽式。這些器件不同于需要最小電壓并“燒盡”多余電壓的線性穩壓器。

General Description

The MCP16361/2/3 family of devices are highly integrated, high-efficiency, fixed-frequency, step-down DC-DC converters in a compact 8-lead 3x3 mm VDFN package that operates from input voltage sources up to 48V. Integrated features include a high-side switch, fixed-frequency Peak Current Mode Control, Internal Compensation, Power Good, Peak Current Limit and Overtemperature Protection. The MCP16361/2/3 provides all the active functions for local DC-DC conversion, with fast transient response and accurate regulation.

High efficiency conversion is achieved by integrating the current-limited, low-resistance, high-speed N-Channel MOSFET and associated drive circuitry. High switching frequency minimizes the size of external filtering components resulting in a small size solution.

The MCP16361/2/3 can supply 3A of continuous current while regulating the output voltage from 2.0V to 24V. An integrated, high-performance peak current mode architecture keeps the output voltage tightly regulated, even during input voltage steps and output current transient conditions that are common in power systems.

The MCP16361 is capable of running in PFM/PWM mode. It switches in PFM mode for light load conditions and for large buck conversion ratios. This results in a higher efficiency over all load ranges.

By comparison, the MCP16362 runs in PWM-only mode, and is recommended for applications in which the low-frequency component associated with PFM mode of operation is not desirable.

Besides the two aforementioned options, the MCP16363 is designed for EMI constrained applications where reduced peak emissions are required. This is achieved by sweeping the switching frequency over a 10 range above the 2.2 MHz nominal value.

Output voltage is set with an external resistor divider. The Power Good output pin will go from logic low to logic high (through an external pull-up resistor) once the output voltage is within 93 of the nominal set point. The EN input is used to turn the device on and off. While off, only a few micro-amps of current are consumed from the input.

The MCP16361/2/3 is offered in a space-saving 8-lead 3x3 mm VDFN wettable flanks surface mount package.

Features

?Input Voltage Range: 4.0V to 48V

?Adjustable Output Voltage Range: 2.0V to 24V

?Integrated N-Channel Buck Switch: 100 m?

?3A Output Current

?2.2 MHz Fixed Frequency

?Shutdown Current: 5 μA typical

?Quiescent Current: 18 μA typical (not switching)

?Device Selectable Switching Mode

-Automatic Pulse Frequency Modulation/Pulse Width Modulation (PFM/PWM) Operation - MCP16361

-PWM only Mode of Operation - MCP16362

-PWM only Mode of Operation with Switching Frequency Dithering for EMI constrained applications - MCP16363

?Power Good Output

?Undervoltage Lockout (UVLO)

?Peak Current Mode Control

?Internal Compensation

?Internal Soft-Start

?Internal Bootstrap Diode

?Cycle-by-Cycle Peak Current Limit

?Overtemperature Protection

?Available Package: 8-lead 3x3 mm wettable flanks VDFN (see Package Type)

Applications

?Automotive DC/DC and 48V Systems

?Microcontroller Bias Supply

?24V Industrial Input DC-DC Conversion

?Set-Top Boxes, DSL Cable Modems

?Wall Cube Regulation

?SLA Battery-Powered Devices

?AC-DC Digital Control Power Sources

?Power Meters

?Medical and Health Care

?Distributed Power Supplies