首頁>PCA9541APW/01>規格書詳情

PCA9541APW/01集成電路(IC)的專用規格書PDF中文資料

PCA9541APW/01
廠商型號

PCA9541APW/01

參數屬性

PCA9541APW/01 封裝/外殼為16-TSSOP(0.173",4.40mm 寬);包裝為管件;類別為集成電路(IC)的專用;PCA9541APW/01應用范圍:2 通道 I2C 多路復用器;產品描述:IC INTERFACE SPECIALIZED 16TSSOP

功能描述

2-to-1 I2C-bus master selector with interrupt logic and reset

文件大小

383.93 Kbytes

頁面數量

45

生產廠商 NXP Semiconductors
企業簡稱

nxp恩智浦

中文名稱

恩智浦半導體公司官網

原廠標識
數據手冊

下載地址一下載地址二到原廠下載

更新時間

2024-12-23 19:46:00

PCA9541APW/01規格書詳情

General description

The PCA9541A is a 2-to-1 I2C-bus master selector designed for high reliability dual

master I2C-bus applications where system operation is required, even when one master

fails or the controller card is removed for maintenance. The two masters (for example,

primary and back-up) are located on separate I2C-buses that connect to the same

downstream I2C-bus slave devices. I2C-bus commands are sent by either I2C-bus master and are used to select one master at a time. Either master at any time can gain control of the slave devices if the other master is disabled or removed from the system. The failed master is isolated from the system and does not affect communication between the on-line master and the slave devices on the downstream I2C-bus.

Two versions are offered for different architectures. PCA9541A/01 with channel 0

selected at start-up, and PCA9541A/03 with no channel selected after start-up.

The interrupt outputs are used to provide an indication of which master has control of the bus. One interrupt input (INT_IN) collects downstream information and propagates it to the 2 upstream I2C-buses (INT0 and INT1) if enabled. INT0 and INT1 are also used to let the previous bus master know that it is not in control of the bus anymore and to indicate the completion of the bus recovery/initialization sequence. If the masking option is set, those interrupts can be disabled and do not generate an interrupt.

A bus recovery/initialization if enabled sends nine clock pulses, a not acknowledge, and a

STOP condition in order to set the downstream I2C-bus devices to an initialized state

before actually switching the channel to the selected master. An interrupt is sent to the upstream channel when the recovery/initialization procedure is completed. An internal bus sensor senses the downstream I2C-bus traffic and generates an interrupt if a channel switch occurs during a non-idle bus condition. This function is enabled when

the PCA9541A recovery/initialization is not used. The interrupt signal informs the master

that an external I2C-bus recovery/initialization must be performed. It can be disabled and an interrupt is not generated. The pass gates of the switches are constructed such that the VDD pin can be used to limit the maximum high voltage, which will be passed by the PCA9541A. This allows the use of different bus voltages on each pair, so that 1.8 V, 2.5 V, or 3.3 V devices can communicate with 5 V devices without any additional protection. The PCA9541A does not isolate the capacitive loading on either side of the device, so the designer must take into account all trace and device capacitances on both sides of the device, and pull-up resistors must be used on all channels. External pull-up resistors pull the bus to the desired voltage level for each channel. All I/O pins are 6.0 V tolerant.An active LOW reset input allows the PCA9541A to be initialized. Pulling the RESET pin LOW resets the I2C-bus state machine and configures the device to its default state as does the internal Power-On Reset (POR) function.

Features and benefits

? 2-to-1 bidirectional master selector

? I2C-bus interface logic; compatible with SMBus standards

? PCA9541A/01 powers up with Channel 0 selected

? PCA9541A/03 powers up with no channel selected and either master can take control

of the bus

? Active LOW interrupt input

? 2 active LOW interrupt outputs

? Active LOW reset input

? 4 address pins allowing up to 16 devices on the I2C-bus

? Channel selection via I2C-bus

? Bus initialization/recovery function

? Bus traffic sensor

? Low Ron switches

? Allows voltage level translation between 1.8 V, 2.5 V, 3.3 V and 5 V buses

? No glitch on power-up

? Supports hot insertion

? Software identical for both masters

? Low standby current

? Operating power supply voltage range of 2.3 V to 5.5 V

? 6.0 V tolerant inputs

? 0 Hz to 400 kHz clock frequency

? ESD protection exceeds 2000 V HBM per JESD22-A114 and 1000 V CDM per

JESD22-C101

? Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA

? Packages offered: SO16, TSSOP16, HVQFN16

產品屬性

  • 產品編號:

    PCA9541APW/01,118

  • 制造商:

    NXP USA Inc.

  • 類別:

    集成電路(IC) > 專用

  • 包裝:

    管件

  • 應用:

    2 通道 I2C 多路復用器

  • 接口:

    I2C,SMBus

  • 電壓 - 供電:

    2.3V ~ 5.5V

  • 封裝/外殼:

    16-TSSOP(0.173",4.40mm 寬)

  • 供應商器件封裝:

    16-TSSOP

  • 安裝類型:

    表面貼裝型

  • 描述:

    IC INTERFACE SPECIALIZED 16TSSOP

供應商 型號 品牌 批號 封裝 庫存 備注 價格
NXP
1230+
TSSOP16
15
一級代理,專注軍工、汽車、醫療、工業、新能源、電力
詢價
NXP/恩智浦
21+
NA
5000
只做原裝,一定有貨,不止網上數量,量多可訂貨!
詢價
NXP(恩智浦)
23+
9865
原裝正品,假一賠十
詢價
NXP/恩智浦
1950+
TSSOP16
6852
只做原裝正品現貨!或訂貨假一賠十!
詢價
NXP(恩智浦)
2021+
TSSOP-16
499
詢價
NXP
22+
NA
545
原裝正品支持實單
詢價
NXP(恩智浦)
23+
TSSOP16
25524
原裝正品,現貨庫存,1小時內發貨
詢價
NXP
23+
TSSOP16
6850
只做原廠原裝正品現貨!假一賠十!
詢價
NXP/恩智浦
22+
TSOP16
18000
原裝現貨原盒原包.假一罰十
詢價
NXP(恩智浦)
23+
NA
6000
原裝現貨訂貨價格優勢
詢價