PM4354中文資料PMC數(shù)據(jù)手冊(cè)PDF規(guī)格書

DESCRIPTION

The PM4354 Four Channel Combined E1/T1/J1 Transceiver and Framer (COMET-QUAD) is a feature-rich monolithic integrated circuit suitable for use in long haul and short haul T1, J1 and E1 systems with a minimum of external circuitry. The COMET-QUAD is software configurable, allowing feature selection without changes to external wiring.

FEATURES

? Monolithic device which integrates four, full-featured T1 and E1 framers and T1 and E1 short haul and long haul line interfaces.

? Software selectable between T1/J1 and E1 operation on a per-device basis.

? Meets or exceeds T1 and E1 shorthaul and longhaul network access specifications including ANSI T1.102, T1.403, T1.408, AT&T TR 62411, ITU-T G.703, G.704 as well as ETSI 300-011, CTR-4, CTR- 12 and CTR-13.

? Provides encoding and decoding of B8ZS, HDB3 and AMI line codes.

? Provides receive equalization, clock recovery and line performance monitoring.

? Provides transmit and receive jitter attenuation.

? Provides digitally programmable long haul and short haul line build out.

? Provides four full-featured HDLC controllers, each with 128-byte transmit and receive FIFO buffers.

? Automatically generates and transmits DS-1 performance report messages to ANSI T1.231 and ANSI T1.408 specifications.

? Supports Nx64Kbit/s fractional bandwidth backplane.

? Supports transfer of PCM data to/from 1.544MHz and 2.048MHz system-side devices. Also supports a fractional T1 or E1 system interface with independent backplane receive/backplane transmit Nx64Kbit/s rates. Supports a 2.048 MHz system-side interface for T1 mode without external clock gapping.

? Supports 8.192 Mbit/s, H-100 compatible, H-MVIP on the system interface for all T1 or E1 links, a separate 8.192 Mbit/s H-MVIP system interface for all T1 or E1 CAS channels and a separate 8.192 Mbit/s H-MVIP system interface for all T1 or E1 CCS, V5.1/V5.2, and GR.303 channels.

? Provides a selectable, per channel independent de-jittered T1 or E1 recovered clock for system timing and redundancy.

? Provides PRBS generators and detectors on each tributary for error testing at DS1, E1 and Nx64Kbit/s rates as recommended in ITU-T O.151 and O.152.

? Provides robbed bit signaling extraction and insertion on a per-DS0 basis.

? Register level compatibility with the PM4388 TOCTL Octal T1 Framer, the PM6388 EOCTL Octal E1 Framer, the PM4351 COMET E1/T1 transceiver, and the PM8315 TEMUX T1/E1 Framer with integrated Mapper and M13 MUX.

? Provides an 8-bit microprocessor bus interface for configuration, control, and status monitoring.

? Uses line rate system clock.

? Provides an IEEE P1149.1 (JTAG) compliant test access port (TAP) and controller for boundary scan test.

? Implemented in a low power 5 V tolerant 2.5/3.3 V CMOS technology.

? Available in a high density 208-pin fine pitch PBGA (17 mm by 17 mm) package.

? Provides a -40°C to +85°C Industrial temperature operating range.

APPLICATIONS

? Wireless Base Station, Transceiver or Digital Loop Carrier

? DSLAM

? Metro Optical Access Equipment

? Voice Gateway

? Enterprise Router

? SONET/SDH Multiplexer

? Channel and Data Service Units (CSU/DSU)

? Digital Private Branch Exchanges (PBX)

? Digital Access Cross-Connect Systems (DACS)

? ISDN Primary Rate Interfaces (PRI)

? Test Equipment