PN7150B0HN/C110XX中文資料恩智浦?jǐn)?shù)據(jù)手冊PDF規(guī)格書

2 General description

Plug′n play and high-performance full NFC solution PN7150 is a full NFC controller solution with integrated firmware and NCI interface designed for contactless communication at 13.56 MHz. It is compatible with NFC forum requirements.

PN7150 is designed based on learnings from previous NXP NFC device generation. It is the ideal solution for rapidly integrating NFC technology in any application, especially those running O/S environment like Linux and Android, reducing Bill of Material (BOM) size and cost, thanks to:

? Full NFC forum compliancy (see [1]) with small form factor antenna

? Embedded NFC firmware providing all NFC protocols as pre-integrated feature

? Direct connection to the main host or microcontroller, by I2C-bus physical and NCI protocol

? Ultra-low power consumption in polling loop mode

? Highly efficient integrated power management unit (PMU) allowing direct supply from a battery

PN7150 embeds a new generation RF contactless front-end supporting various transmission modes according to NFCIP-1 and NFCIP-2, ISO/IEC 14443, ISO/IEC 15693, MIFARE Classic IC-based card and FeliCa card specifications. It embeds an Arm Cortex-M0 microcontroller core loaded with the integrated firmware supporting the NCI 1.0 host communication. It also allows to provide a higher output power by supplying the transmitter output stage from 3.0 V to 4.75 V.

The contactless front-end design brings a major performance step-up with on one hand a higher sensitivity and on the other hand the capability to work in active load modulation communication enabling the support of small antenna form factor.

Figure 1 lists the supported transmission modes. For contactless card functionality, the PN7150 can act autonomously if previously configured by the host in such a manner.

PN7150 integrated firmware provides an easy integration and validation cycle as all the NFC real-time constraints, protocols and device discovery (polling loop) are being taken care internally. In few NCI commands, host SW can configure the PN7150 to notify for card or peer detection and start communicating with them.

3 Features and benefits

? Includes NXP ISO/IEC14443-A and Innovatron ISO/IEC14443-B intellectual property licensing rights

? Arm Cortex-M0 microcontroller core

? Highly integrated demodulator and decoder

? Buffered output drivers to connect an antenna with minimum number of external components

? Integrated RF level detector

? Integrated Polling Loop for automatic device discovery

? RF protocols supported

– NFCIP-1, NFCIP-2 protocol (see [8] and [11])

– ISO/IEC 14443A, ISO/IEC 14443B PICC, NFC Forum T4T modes via host interface (see [3])

– NFC Forum T3T via host interface

– ISO/IEC 14443A, ISO/IEC 14443B PCD designed according to NFC Forum digital protocol T4T platform

and ISO-DEP (see [1])

– FeliCa PCD mode

– MIFARE Classic PCD encryption mechanism (MIFARE Classic 1K/4K)

– NFC Forum tag 1 to 5 (MIFARE Ultralight, Jewel, Open FeliCa tag, MIFARE DESFire) (see [1])

– ISO/IEC 15693/ICODE VCD mode (see [9])

? Supported host interfaces

– NCI protocol interface according to NFC Forum standardization (see [2])

– I2C-bus High-speed mode (see [4])

? Integrated power management unit

– Direct connection to a battery (2.3 V to 5.5 V voltage supply range)

– Support different Hard Power-Down/Standby states activated by firmware

– Autonomous mode when host is shut down

? Automatic wake-up via RF field, internal timer and I2C-bus interface

? Integrated non-volatile memory to store data and executable code for customization

4 Applications

? All devices requiring NFC functionality especially those running in an Android or Linux environment

? TVs, set-top boxes, blu-ray decoders, audio devices

? Home automation, gateways, wireless routers

? Home appliances

? Wearables, remote controls, healthcare, fitness

? Printers, IP phones, gaming consoles, accessories