PN7360AUHNRF/IF射頻/中頻RFID的RFID射頻接入監(jiān)控IC規(guī)格書PDF中文資料

description

The PN736X family is a family of 32-bit ARM Cortex-M0-based NFC microcontrollers

offering high performance and low power consumption. It has a simple instruction set and

memory addressing along with a reduced code size compared to existing architectures.

PN736Xoffers an all in one solution, with features such as NFC, microcontroller, and

software in a single chip. It operates at CPU frequencies of up to 20 MHz. It is part of the

PN7462AU product family which offers a common set of features, library and tools.

The peripheral complement of the PN736X microcontroller includes 160/80 kB of flash

memory, 12 kB of SRAM data memory and 4 kB EEPROM. It also includes one host

interface with either high-speed mode I2C-bus, SPI, USB or high-speed UART, and two

master interfaces, SPI and Fast-mode Plus I2C-bus. Four general-purpose counter/

timers, a random number generator, one CRC coprocessor and up to 21 general-purpose

I/O pins are also available.

The PN736X NFC microcontroller offer a one chip solution to build contactless

applications. It is equipped with a highly integrated high-power output NFC-IC for

contactless communication at 13.56 MHz enabling EMV-compliance on RF level, without

additional external active components.

PN736X supports the following operating modes:

? ISO/IEC 14443-A and B, MIFARE

? JIS X 6319-4 (comparable with FeliCa scheme)

? ISO/IEC 15693, ICODE, ISO/IEC 18000-3 mode 3

? NFC protocols - tag reader/writer, P2P

? ISO/IEC 14443- type A card emulation

? EMVCo compliance

Features

Integrated contactless interface frontend

? High RF output power frontend IC for transfer speed up to 848 kbit/s

? NFC IP1 and NFC IP2 support

? Full NFC tag support (type 1, type 2, type 3, type 4A and type 4B)

? P2P active and passive, target and initiator

? Card emulation ISO14443 type A

? ISO/IEC 14443 type A and type B

? MIFARE classic card

? ISO/IEC 15693, and ISO/IEC 18000-3 mode 3

? Low-power card detection

? Dynamic Power Control (DPC) support

? Compliance with EMV contactless protocol specification

? Compliance with NFC standards

Cortex-M0 microcontroller

? Processor core

– ARM Cortex: 32-bit M0 processor

– Built-in Nested Vectored Interrupt Controller (NVIC)

– Non-maskable interrupt

– 24-bit system tick timer

– Running frequency of up to 20 MHz

– Clock management to enable low power consumption

? Memory

– Flash: 160 (PN7362) / 80 kB (PN7360)

– SRAM: 12 kB

– EEPROM: 4 kB

– 40 kB boot ROM included, including USB mass storage primary boot loader for code

download

? Debug option

– Serial Wire Debug (SWD) interface

? Peripherals

– Host interface:

– USB 2.0 full speed with USB 3.0 hub connection capability

– HSUART for serial communication, supporting standards speeds from 9600 bauds to

115200 bauds, and faster speed up to 1.288 Mbit/s

– SPI with half-duplex and full duplex capability with speeds up to 7 Mbit/s

– I2C supporting standard mode, fast mode and high-speed mode with multiple address

support

– Master interface:

– SPI with half-duplex capability from 1 Mbit/s to 6.78 Mbit/s

– I2C supporting standard mode, fast mode, fast mode plus and clock stretching

? Up to 21 General-Purpose I/O (GPIO) with configurable pull-up/pull-down resistors

? GPIO1 to GPIO12 can be used as edge and level sensitive interrupt sources

? Power

– Two reduced power modes: standby mode and hard power-down mode

– Supports suspend mode for USB host interface

– Processor wake-up from hard power-down mode, standby mode, suspend mode via

host interface, GPIOs, RF field detection

– Integrated PMU to adjust internal regulators automatically, to minimize the power

consumption during all possible power modes

– Power-on reset

– RF supply: external, or using an integrated LDO (TX LDO, configurable with 3 V, 3.3

V, 3.6 V, 4.5 V, and 4.75 V)

– Pad voltage supply: external 3.3 V or 1.8 V, or using an integrated LDO (3.3 V

supply)

? Timers

– Four general-purpose timers

– Programmable Watchdog Timer (WDT)

? CRC coprocessor

? Random number generator

? Clocks

– Crystal oscillator at 27.12 MHz

– Dedicated PLL at 48 MHz for the USB

– Integrated HFO 20 MHz and LFO 365 kHz

? General

– HVQFN64 package

– Temperature range: -40 °C to +85 °C

Applications

? Physical access control

? Gaming

? USB NFC reader, including dual interface smart card readers

? Home banking, payment readers EMVCo compliant

? High integration devices

? NFC applications