SAF7847HL集成電路（IC）的編碼器解碼器轉(zhuǎn)換器規(guī)格書(shū)PDF中文資料

General description

The SAF784x is a single-chip solution CD audio decoder with on-chip MP3 and WMA

decoding, digital servo, audio DAC, sample-rate converter, preamplifier, laser driver and

integrated ARM7TDMI-S microprocessor. The device contains all of the required ROM

and RAM, including an internal re-programmable Flash ROM, and is targeted at low-cost

compressed audio CD applications. The design is a one-chip CD audio decoder IC, with

additions to allow low-cost system implementation of MP3 and WMA decoding.

Features

2.1 Features

- Channel decoder and digital servo

- 32-bit embedded ARM7 RISC microprocessor supporting both 32-bit and 16-bit

(‘Thumb’) instruction sets

- Maximum ARM operating frequency of 76 MHz, equivalent to 68 MIPS

- Decoding of compressed audio stream (MP3/WMA) on ARM7 core

- All memories required for MP3/WMA decoding embedded on chip: combination of

130 kB mask-programmed internal program ROM (to reduce wait-states on

high-speed code, e.g. decompression algorithms), 42 kB boot ROM, 64 kB of internal

re-programmable Flash ROM (for simple re-programming of application code) 110 kB

internal SRAM

- Programmable clock frequency for ARM microprocessor - allowing users to trade-off

power consumption and processing power depending on requirements

- Block decoder hardware to perform C3 error correction

- Sample-rate converter circuit to convert compressed audio sample rates (in the range

8 kHz to 48 kHz) to an output rate of 44.1 kHz

- Microprocessor access to digital representations of the diode input signals from the

optical pickup; the microprocessor can also generate the servo output signals RA, FO,

SL, allowing the possibility of additional servo algorithms in software

- Programmable PDM outputs (effectively sine and cosine) to allow use of stepper motor

for sledge mechanism

- Microprocessor access to audio streams, both from the internal CD decoder and an

external stereo auxiliary input (e.g. an analog source from a tuner, converted to digital

via on-chip ADCs) to allow audio processing algorithms in the ARM microprocessor,

e.g. bass boost, volume control

- Four general-purpose analog inputs (A_IN1 to A_IN4) allowing the ARM

microprocessor access to other external analog signals, e.g. low-cost keypad,

temperature sensor, via on-chip ADCs

- Two additional analog audio inputs (AUX_L, AUX_R) to allow the ARM microprocessor

access to external audio signals (e.g. tuner); allows audio algorithms (e.g. bass boost)

to be performed on external audio signals

- Real-time clock operated from separate 32 kHz crystal; allows low-power Standby

mode with real-time clock still operational

- Watchdog timer

- I2S-bus, S/PDIF, subcode (V4) and subcode sync outputs

- 32 GPIOs

- Two standard UART channels

- Two external interrupt pins

- I2C-bus interface configurable for master or slave modes, supporting 100 kbit/s and

400 kbit/s standards

- Slave I2S-bus mode, in which the channel decoder can synchronize the CD playback

speed to an I2S-bus clock input

- Integrated digital HF/Mirror detector with measurement of minimum and maximum

peak values, amplitude and offset

- Integrated CD-text decoder

- Up to 6′ decode speed, CLV or CAV modes

- LQFP144 package with 0.5 mm pin pitch

- Separate left and right channel digital silence detection available on KILL pins

- Digital silence detection available on loopback data from external source as well as

internal data

- ‘Filterless’ pseudo bit stream audio DAC with minimal external components

- Stereo line outputs for audio DAC

- Loopback mode allowing the use of integrated DAC with external I2S-bus/EIAJ sources

- Compatible with voltage mode mechanisms

- On-chip buffering and filtering of the diode signals from the mechanism in order to

optimize the signals for the decoder and servo parts

- LF (servo) signals converted to digital representations by Sigma-Delta ADCs shared

between pairs of channels to minimize DC offset between channels

- HF part summed from signals D1 to D4 and converted to digital signals by HF 6-bit

ADC

- Selectable DC offset cancellation of quiescent mechanism voltages and dark currents,

digitally controlled; additional fine DC-offset cancellation in digital domain

- Eye pattern monitor system to observe selectable points within the analog pre-amp

- Current and average jitter values available via registers

- On-chip laser power control, up to maximum currents of 120 mA

- Laser on-off control, including ‘soft’-start control - zero-to-nominal output power in

1 ms

- Monitor control and feedback circuit to maintain nominal output power throughout laser

life

- Configured for Nsub (N-substrate) monitor diode

- JTAG interface for device access and ARM code development (compatible with ARM

multi-ICE)

- All digital input pins 5 V tolerant

- Low-latency static memory interface to access a maximum of two 2 MB memory

- This product has been qualified in accordance with AEC-Q100