SAM9X75D1G-I/4TB中文資料微芯科技數(shù)據(jù)手冊PDF規(guī)格書

Features

? CPU Running up to 800 MHz

– ARM926EJ-S Arm Thumb? processor

– 32-Kbyte data cache, 32-Kbyte instruction cache, Memory Management Unit (MMU)

? Memories

– One 176-Kbyte internal ROM

? 80-Kbyte internal ROM embedding a secure bootloader program supporting boot on NAND Flash,

SD Card, SPI or QSPI Flash; bootloader features selectable by OTP bits

? 96-Kbyte ROM for NAND Flash BCH ECC table

– One 64-Kbyte internal SRAM (SRAM0), single cycle access at system speed

– Internal DDR3L SDRAM running at up to 266 MHz

– External Bus Interface (EBI) supporting:

? 8-bit NAND Flash with up to 24-bit programmable multi-bit error correcting code

– One 10-Kbyte OTP memory for secure key storage with Emulation mode (OTP bits are emulated by a

4-Kbyte SRAM (SRAM1))

? System Running up to 266 MHz

– Power-on reset cells, reset controller, shutdown controller, periodic interval timer, watchdog timer

running on internal slow RC oscillator (32 kHz typical) and real-time clock running on slow crystal

oscillator (32.768 kHz)

– Two internal trimmed RC oscillators with typical values: 32 kHz (slow) and 12 MHz (fast)

– Two crystal oscillators: 32.768 kHz (slow) and 20 to 50 MHz (fast)

– One PLL for the system and one PLL optimized for USB high-speed operation (480 MHz)

? One PLL for audio operations, with dedicated output clock

? One PLL in LVDS I/F (LVDS usage only)

? One PLL in MIPI DPHY (MIPI DSI usage only)

– One dual-port 16-channel DMA controller

– Advanced interrupt controller and debug unit

– JTAG port with disable bit in OTP memory

– Two programmable clock output signals

? Low-Power Modes

– Backup mode with RTC, eight 32-bit general purpose backup registers, and shutdown controller to

control the external power supply

– Clock generator and power management controller

– Software-programmable ultra-low power modes: very slow clock operating mode (ULP0) and no-clock

operating mode (ULP1) with fast wake-up capabilities

– Software programmable power optimization capabilities

? Peripherals

– LCD controller with overlay, alpha blending, rotation, scaling and color conversion; up to 720p resolution

? RGB, LVDS, MIPI-DSI interfaces

– 2D graphics controller supporting fill BLT, copy BLT, transparent BLT, blend/alpha BLT, ROP4 BLT (raster

operations) and command ring buffer

– Image sensor controller with ITU-R BT; 601/656/1120 video interface support up to 5 Mpixels; support of

raw Bayer 12, YCbCr, monochrome and JPEG compressed sensors up to 12 bits

? MIPI CSI2 I/F support

? 12-bit parallel I/F support

– One high-speed USB device, three high-speed USB hosts with dedicated on-chip transceivers

– One 10/100/1000 Mbps Ethernet Mac controller with IEEE-1588 and TSN support, RGMII and RMII

support

– Two 4-bit secure digital multimedia card controllers

– Two CAN FD controllers with timestamping

– One Quad/Octal SPI controller

– Two 3-channel 32-bit timers/counters

– Two high-resolution (64-bit) periodic interval timers

– One synchronous serial controller

– One inter-IC sound multi-channel controller with TDM support

– One audio class D controller with single-ended or bridge-tied load connection to power stage

– One 4-channel 16-bit PWM controller

– Thirteen FLEXCOMs (USART, SPI and TWI/I2C)

– One 8-channel, 12-bit, analog-to-digital converter with 4/5 wires resistive touchscreen support

? Hardware Cryptography

– SHA (SHA1, SHA224, SHA256, SHA384, SHA512) and HMAC compliant with FIPS PUB 180

– AES: 256-, 192-, 128-bit key algorithms compliant with FIPS PUB 197

– AES/SHA tight coupling for IPsec hardware acceleration

– TDES: 2-key or 3-key algorithms compliant with FIPS PUB 46

– True random number generator compliant with NIST Special Publication 800-22 Test Suite and FIPS PUBs

140-2 and 140-3

– Key bus providing private key transfers between AES, TDES, TRNG, OTPC

– Physical Unclonable Function (PUF) including NIST SP 800-90B (DRNG) and embedding four Kbytes of

SRAM (PUFSRAM)

? I/O Ports

– Four 32-bit parallel input/output controllers

– Up to 106 programmable I/O lines multiplexed with up to four peripheral I/Os

– Input change interrupt capability on each I/O line, optional Schmitt trigger input

– Individually programmable open-drain, pull-up and pull-down resistors, synchronous output

– General-purpose analog and digital inputs tolerant to positive and negative current injection

? Package

– 16x16 mm2, 0.8-mm pitch, 243-ball BGA optimized for standard class PCB layout (down to four layers)

? Design for low ElectroMagnetic Interference (EMI)

– Slewrate-controlled I/Os

– DDR PHY with impedance-calibrated drivers

– Spread spectrum PLLs

– BGA power/ground ball assignment to provide optimum decoupling capacitors placement

? Operating Conditions

– Junction temperature (TJ) range: -40°C to +125°C

– Ambient temperature (TA) range: -40°C to +85°C