首頁>SC26C198>規格書詳情

SC26C198中文資料飛利浦數據手冊PDF規格書

SC26C198
廠商型號

SC26C198

功能描述

Octal UART with TTL compatibility at 3.3V and 5V supply voltages

文件大小

358.15 Kbytes

頁面數量

49

生產廠商 NXP Semiconductors
企業簡稱

Philips飛利浦

中文名稱

荷蘭皇家飛利浦官網

原廠標識
數據手冊

下載地址一下載地址二到原廠下載

更新時間

2024-12-25 15:42:00

SC26C198規格書詳情

DESCRIPTION

The Philips 26C198 Octal UART is a single chip CMOS–LSI communications device that provides 8 full-duplex asynchronous channels with significantly deeper 16 byte FIFOs, Automatic in–band flow control using Xon/Xoff characters defined by the user and address recognition in the wake up mode. Synchronous bus interface is used for all communication between host and OCTART. It is fabricated using Philips 1.0 micron CMOS technology that combines the benefits of low cost, high density and low power consumption.

The operating speed of each receiver and transmitter can be selected independently from one of 22 fixed baud rates, a 16X clock derived from one of two programmable baud rate counters or one of three external 16X clocks (1 available at 1x clock rate). The baud rate generator and counter can operate directly from a crystal or from seven other external or internal clock inputs. The ability to independently program the operating speed of the receiver and transmitter makes the Octal UART particularly attractive for dual speed full duplex channel applications such as clustered terminal systems. The receivers and transmitters are buffered with FIFOs of 16 characters to minimize the potential for receiver overrun and to reduce interrupt overhead. In addition, a handshaking capability and in–band flow control are provided to disable a remote UART transmitter when the receiver buffer is full or nearly so.

To minimize interrupt overhead an interrupt arbitration system is included which reports the context of the interrupting UART via direct access or through the modification of the interrupt vector. The context of the interrupt is reported as channel number, type of device interrupting ( receiver COS etc.) and, for transmitters or receivers, the fill level of the FIFO.

The Octal UART provides a power down mode in which the oscillator is stopped but the register contents are maintained. This results in reduced power consumption of several orders of magnitudes. The Octal UART is fully TTL compatible when operating from a single +5V power supply. Operation at 3.3 volts is maintained with CMOS interface levels.

The device also offered in a version which maintains TTL input and output levels while operating with a 3.3 volt power supply.

FEATURES

? Single 3.3v power supply

? Eight Philips industry standard full duplex UART channels

? Sixteen byte receiver FIFOs for each UART

? Sixteen byte transmit FIFOs for each UART

? In band flow control using programmable Xon/Xoff characters

? Flow control using CTSN RTSN hardware handshaking

? Automatic address detection in multi-drop mode

? Three byte general purpose character recognition

? Fast data bus, 30 ns data bus release time, 125 ns bus cycle time

? Programmable interrupt priorities

? Automatic identification of highest priority interrupt pending

? Global interrupt and control registers ease setup and interrupt handling

? Vectored interrupts with programmable interrupt vector formats

– Interrupt vector modified with channel number

– Interrupt vector modified with channel number and channel type

– Interrupt vector not modified

? IACKN and DACKN signal pins

? Watch dog timer for each receiver (64 receive clock counts)

? Programmable Data Formats:

– 5 to 8 data bits plus parity

– Odd, even force or no parity

– 1, 1.5 or 2 stop bits

? Flexible baud rate selection for receivers and transmitters:

– 22 fixed rates; 50 – 230.4K baud or 100 to 460.8K baud

– Additional non–standard rates to 500K baud with internal generators

– Two reload–counters provide additional programmable baud rate generation

– External 1x or 16x clock inputs

– Simplified baud rate selection

? 1 MHz 1x and 16x data rates full duplex all channels.

? Parity, framing and overrun error detection

? False start bit detection

? Line break detection and generation

? Programmable channel mode

– Normal(full duplex)

– Diagnostic modes

automatic echo

local loop back

emote loop back

? Four I/O ports per UART for modem controls, clocks, RTSN, I/O etc.

– All I/O ports equipped with ”Change of State Detectors”

? Two global inputs and two global outputs for general purpose I/O

? Power down mode

? On chip crystal oscillator, 2–8 MHz

? TTL input levels. Outputs switch between full VCC and VSS

? High speed CMOS technology

? 68 pin PLCC

產品屬性

  • 型號:

    SC26C198

  • 制造商:

    PHILIPS

  • 制造商全稱:

    NXP Semiconductors

  • 功能描述:

    Octal UART with TTL compatibility at 3.3V and 5V supply voltages

供應商 型號 品牌 批號 封裝 庫存 備注 價格
NXP/恩智浦
23+
PLCC84
11200
原廠授權一級代理、全球訂貨優勢渠道、可提供一站式BO
詢價
PHILIPS
PLCC-84
699839
集團化配單-有更多數量-免費送樣-原包裝正品現貨-正規
詢價
AN
2016+
PLCC
6528
只做原廠原裝現貨!終端客戶個別型號可以免費送樣品!
詢價
PHILIPS
23+
PLCC84
4500
全新原裝、誠信經營、公司現貨銷售!
詢價
NA
24+
99
原裝現貨假一賠十
詢價
PHILIPS
2020+
PLCC-84
80000
只做自己庫存,全新原裝進口正品假一賠百,可開13%增
詢價
PHILIPS
18+
PLCC84
85600
保證進口原裝可開17%增值稅發票
詢價
PHILIPS
9627+
PLCC-84
6000
絕對原裝自己現貨
詢價
PHILIPS/飛利浦
23+
NA/
3445
原廠直銷,現貨供應,賬期支持!
詢價
PHILIPS
23+
PLCC84
12300
詢價