STM32F303開發(fā)板套件編程器的評估板-嵌入式-MCUDSP規(guī)格書PDF中文資料

Description

The STM32F302xB/STM32F302xC family is based on the high-performance ARM? Cortex?-M4 32-bit RISC core with FPU operating at a frequency of up to 72 MHz, and embedding a floating point unit (FPU), a memory protection unit (MPU) and an embedded trace macrocell (ETM). The family incorporates high-speed embedded memories (up to 256 Kbytes of Flash memory, up to 40 Kbytes of SRAM) and an extensive range of enhanced I/Os and peripherals connected to two APB buses.

Features

? Core: ARM? Cortex?-M4 32-bit CPU with FPU (72 MHz max), single-cycle multiplication and HW division, DSP instruction and MPU (memory protection unit)

? Operating conditions:

– VDD, VDDA voltage range: 2.0 V to 3.6 V

? Memories

– 128 to 256 Kbytes of Flash memory

– Up to 40 Kbytes of SRAM, with HW parity check implemented on the first 16 Kbytes.

? CRC calculation unit

? Reset and supply management

– Power-on/Power-down reset (POR/PDR)

– Programmable voltage detector (PVD)

– Low-power modes: Sleep, Stop and Standby

– VBAT supply for RTC and backup registers

? Clock management

– 4 to 32 MHz crystal oscillator

– 32 kHz oscillator for RTC with calibration

– Internal 8 MHz RC with x 16 PLL option

– Internal 40 kHz oscillator

? Up to 87 fast I/Os

– All mappable on external interrupt vectors

– Several 5 V-tolerant

? Interconnect matrix

? 12-channel DMA controller

? Two ADCs 0.20 μS (up to 17 channels) with selectable resolution of 12/10/8/6 bits, 0 to 3.6 V conversion range, single ended/differential input, separate analog supply from 2 to 3.6 V

? One 12-bit DAC channel with analog supply from 2.4 to 3.6 V

? Four fast rail-to-rail analog comparators with analog supply from 2 to 3.6 V

? Two operational amplifiers that can be used in PGA mode, all terminals accessible with analog supply from 2.4 to 3.6 V

? Up to 24 capacitive sensing channels supporting touchkey, linear and rotary touch sensors

? Up to 11 timers

– One 32-bit timer and two 16-bit timers with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input

– One 16-bit 6-channel advanced-control timer, with up to 6 PWM channels, deadtime generation and emergency stop

– One 16-bit timer with 2 IC/OCs, 1 OCN/PWM, deadtime generation and emergency stop

– Two 16-bit timers with IC/OC/OCN/PWM, deadtime generation and emergency stop

– Two watchdog timers (independent, window)

– SysTick timer: 24-bit downcounter

– One 16-bit basic timer to drive the DAC

? Calendar RTC with Alarm, periodic wakeup from Stop/Standby

? Communication interfaces

– CAN interface (2.0B Active)

– Two I2C Fast mode plus (1 Mbit/s) with 20 mA current sink, SMBus/PMBus, wakeup from STOP

– Up to five USART/UARTs (ISO 7816 interface, LIN, IrDA, modem control)

– Up to three SPIs, two with multiplexed half/full duplex I2S interface, 4 to 16 programmable bit frames

– USB 2.0 full speed interface

– Infrared transmitter

? Serial wire debug, Cortex?-M4 with FPU ETM, JTAG

? 96-bit unique ID