USB5826C集成電路（IC）的控制器規格書PDF中文資料

USB5826C屬于集成電路（IC）的控制器。由微芯科技股份有限公司制造生產的USB5826C控制器該系列產品主要用于在采用不同通信協議和/或信令方法的端點之間提供信息連接。示例包括將 I2C 總線連接到 UART，將 USB 連接到 I2C、SPI、以太網或 UART、以太網 MAC 和 PHY 等的器件。此外，還包括用于通過為點對點通信設計的接口建立多路連接的器件，例如 USB 集線器控制器。

General Description

The Microchip USB5826C hub is a low-power, OEM configurable, USB 3.2 Gen 1 hub controller with 6 downstream

ports and advanced features for embedded USB applications. The USB5826C is fully compliant with the Universal Serial

Bus Revision 3.1 Specification and USB 2.0 Link Power Management Addendum. The USB5826C supports 5 Gbps

SuperSpeed (SS), 480 Mbps Hi-Speed (HS), 12 Mbps Full-Speed (FS), and 1.5 Mbps Low-Speed (LS) USB downstream

devices on all enabled downstream ports.

The USB5826C supports the legacy USB speeds (HS/FS/LS) through a dedicated USB 2.0 hub controller that is the

culmination of five generations of Microchip hub controller design and experience with proven reliability, interoperability,

and device compatibility. The SuperSpeed hub controller operates in parallel with the USB 2.0 hub controller, decoupling

the 5 Gbps SS data transfers from bottlenecks due to the slower USB 2.0 traffic.

The USB5826C hub feature controller enables OEMs to configure their system using “Configuration Straps.” These

straps simplify the configuration process, assigning default values to USB 3.2 Gen 1 ports and GPIOs. OEMs can disable

ports, enable battery charging, and define GPIO functions as default assignments on power-up, removing the need

for OTP or external SPI ROM.

The USB5826C supports downstream battery charging via the integrated battery charger detection circuitry, which supports

the USB-IF Battery Charging (BC1.2) detection method and most Apple devices. The USB5826C provides the

battery charging handshake and supports the following USB-IF BC1.2 charging profiles:

? DCP: Dedicated Charging Port (Power brick with no data)

? CDP: Charging Downstream Port (1.5A with data)

? SDP: Standard Downstream Port (0.5A with data)

? Custom profiles loaded via SMBus or OTP

Additionally, the USB5826C includes many powerful and unique features such as:

The Hub Feature Controller, which provides an internal USB device dedicated for use as a USB to I2C/UART/SPI/

GPIO interface, allowing external circuits or devices to be monitored, controlled, or configured via the USB interface.

PortSwap, which adds per-port programmability to USB differential-pair pin locations. PortSwap allows direct alignment

of USB signals (D+/D-) to connectors to avoid uneven trace length or crossing of the USB differential signals on the

PCB.

PHYBoost, which provides programmable levels of Hi-Speed USB signal drive strength

in the downstream port transceivers. PHYBoost attempts to restore USB signal integrity

in a compromised system environment. The graphic on the right shows an example of

Hi-Speed USB eye diagrams before and after PHYBoost signal integrity restoration. in

a compromised system environment.

VariSense, which controls the USB receiver sensitivity enabling programmable levels of USB signal receive sensitivity.

This capability allows operation in a sub-optimal system environment, such as when a captive USB cable is used.

Port Split, which allows for the USB3.1 Gen1 and USB2.0 portions of downstream ports 3 and 4 to operate independently

and enumerate two separate devices in parallel in special applications.

USB Power Delivery Billboard Device, which allows an internal device to enumerate as a Billboard class device when

a Power Delivery Alternate Mode negotiation has failed. The Billboard device will enumerate temporarily to the host PC

when a failure occurs, as indicated by a digital signal from an external Power Delivery controller.

The USB5826C can be configured for operation through internal default settings. Custom OEM configurations are supported

through external SPI ROM or OTP ROM. All port control signal pins are under firmware control in order to allow

for maximum operational flexibility, and are available as GPIOs for customer specific use.

The USB5826C is available in commercial (0°C to +70°C) and industrial (-40°C to +85°C) temperature ranges. An internal

block diagram of the USB5826C is shown in Figure 2-1.

Highlights

? USB Hub Feature Controller IC Hub with:

- 2 USB 3.1 Gen 1 USB Type-C? downstream ports

- 2 USB 3.1 Gen 1 legacy downstream ports

- 2 USB 2.0 downstream ports

- Legacy upstream port

? USB-IF Battery Charger revision 1.2 support on

up & downstream ports (DCP, CDP, SDP)

? Internal Hub Feature Controller device enables:

- USB to I2C/SPI/GPIO bridge endpoint support

- USB to internal hub register write and read

? USB Link Power Management (LPM) support

? Enhanced OEM configuration options available

through either OTP or SPI ROM

? USB-IF certified, supporting latest

Engineering Change Notices for compliance with

USB-IF logo testing for new USB Type-C?

industry initiative (Revision C or newer only)

- Header Packet Timer (TD7.9, TD7.11, TD7.26)

- Power Management Timer (TD7.18, TD7.20, TD7.23)

- Unacknowledged Connect and Remote

Wake Test Failure (TD10.25)

? Available in 100-pin (12mm x 12mm) VQFN

RoHS compliant package

? Commercial and industrial grade temperature

support

Target Applications

? Standalone USB Hubs

? Laptop Docks

? PC Motherboards

? PC Monitor Docks

? Multi-function USB 3.2 Gen 1 Peripherals

Key Benefits

? USB 3.2 Gen 1 compliant 5 Gbps, 480 Mbps,

12 Mbps, and 1.5Mbps operation

- 5V tolerant USB 2.0 pins

- 1.32V tolerant USB 3.2 Gen 1 pins

- Integrated termination and pull-up/down resistors

? Native USB Type-C Support

- Integrated Multiplexer on USB Type-C enabled

ports

- USB 3.1 Gen 1 PHYs are disabled until a valid

USB Type-C attach is detected, saving idle power

? Supports battery charging of most popular battery

powered devices on all ports

- USB-IF Battery Charging rev. 1.2 support

(DCP, CDP, SDP)

- Apple? portable product charger emulation

- Chinese YD/T 1591-2006 charger emulation

- Chinese YD/T 1591-2009 charger emulation

- European Union universal mobile charger support

- Support for Microchip UCS100x family of battery

charging controllers

- Supports additional portable devices

? Smart port controller operation

- Firmware handling of companion port power

controllers

? On-chip microcontroller

- manages I/Os, VBUS, and other signals

? 8 KB RAM, 64 KB ROM

? 8 KB One-Time-Programmable (OTP) ROM

- Includes on-chip charge pump

? Configuration programming via OTP ROM,

SPI ROM, or SMBus

? PortSwap

- Configurable USB 2.0 differential pair signal swap

? PHYBoostTM

- Programmable USB transceiver drive strength for

recovering signal integrity

- USB 2.0 Hi-Speed disconnect threshold adjust

(Revision C or newer only)

? VariSenseTM

- Programmable USB receive sensitivity

? Port Split

- USB2.0 and USB3.1 Gen1 port operation can be

split for custom applications using embedded

USB3.x devices in parallel with USB2.0 devices.

? USB Power Delivery Billboard Device Support

- Internal port can enumerate as a Power Delivery

Billboard device to communicate Power Delivery

Alternate Mode negotiation failure cases to USB

host

? Compatible with Microsoft Windows 10, 8, 7, XP,

Apple OS X 10.4+, and Linux hub drivers

? Optimized for low-power operation and low thermal

dissipation

? Package

- 100-pin VQFN (12mm x 12mm)