Overview

The DSCC4 is a DMA Supported Serial Communication Controller with four independent serial channels1). The serial channels are derived from updated protocol logic of the ESCC device family providing a large set of protocol support and variety in serial interface configuration. This allows easy integration to different environments and applications.

Features

Serial Communication Controllers (SCCs)

? Four independent channels

? Full duplex data rates on each channel of up to 10 Mbit/s sync - 2 Mbit/s with DPLL, 2 Mbit/s async

? Full duplex data rate of up to 52 Mbit/s on any two channels in high speed mode (HDLC: Address Mode 0 and extended transparent protocol mode); up to 45 Mbit/s on any two channels in high speed mode (HDLC: PPP modes). The aggregate bandwith for all channels is limited to 108 Mbit/s per direction.

? 17 DWORDs deep receive FIFO per SCC (+ 128 DWORDs central receive FIFO).

? 8 DWORDs deep transmit FIFO per SCC (+ 128 DWORDs central transmit FIFO).

Serial Interface

? On-chip clock generation or external clock sources

? On-chip DPLLs for clock recovery

? Baud rate generator

? Clock gating signals

? Clock gapping capability

? Programmable time-slot capability for connection to TDM interfaces (e.g. T1, E1)

? NRZ, NRZI, FM and Manchester data encoding

? Optional data flow control using modem control lines (RTS, CTS, CD)

? Support of bus configuration by collision detection and resolution

? HDLC/SDLC Protocol Modes

– Automatic flag detection and transmission

– Shared opening and closing flag

– Generation of interframe-time fill ’1’s or flags

– Detection of receive line status

– Zero bit insertion and deletion

– CRC generation and checking (CRC-CCITT or CRC-32)

– Transparent CRC option per channel and/or per frame

– Programmable Preamble (8 bit) with selectable repetition rate

– Error detection (abort, long frame, CRC error, short frames)

? Bit Synchronous PPP Mode

– Bit oriented transmission of HDLC frame (flag, data, CRC, flag)

– Zero bit insertion/deletion

– 15 consecutive ’1’ bits abort sequence

? Octet Synchronous PPP Mode

– Octet oriented transmission of HDLC frame (flag, data, CRC, flag)

– Programmable character map of 32 hard-wired characters (00H-1FH)

– Four programmable characters for additional mapping

– Insertion/deletion of control-escape character (7DH) for mapped characters

? Asynchronous PPP Mode

– Character oriented transmission of HDLC frame (flag, data, CRC, flag)

– Start/stop bit framing of single character

– Programmable character map of 32 hard-wired characters (00H-1FH)

– Four programmable characters for additional mapping

– Insertion/deletion of control-escape character (7DH) for mapped characters

? Asynchronous (ASYNC) Protocol Mode

– Selectable character length (5 to 8 bits)

– Even, odd, forced or no parity generation/checking

– 1 or 2 stop bits

– Break detection/generation

– In-band flow control by XON/XOFF

– Immediate character insertion

– Termination character detection for end of block identification

– Time out detection

– Error detection (parity error, framing error)

? BISYNC Protocol Mode

– Programmable 6/8 bit SYN pattern (MONOSYNC)

– Programmable 12/16 bit SYN pattern (BISYNC)

– Selectable character length (5 to 8 bits)

– Even, odd, forced or no parity generation/checking

– Generation of interframe-time fill ’1’s or SYN characters

– CRC generation (CRC-16 or CRC-CCITT)

– Transparent CRC option per channel and/or per frame

(Continue ...)

PEB20534屬于集成電路（IC） > 專用。英飛凌科技股份公司制造生產的PEB20534專用該系列產品可提供所需的功能，用以將信息源/信宿連到各種復雜或范圍狹窄應用中的傳感器、變送器、致動器、傳輸介質或其他此類端點。例如，汽車安全氣囊驅動器、車身控制和信息娛樂總線、自適應電纜均衡器、智能卡等等。